Hi all … obviously I’m new to this forum so if I do something wrong I apologise 😂 I need your help .. I’ve recently purchased a second hand Vesuvius and wondered if any of you guys had any tips, servicing suggestions and where I could get spares .. .. not knowing anyone else that has one I’m not sure what should be and what shouldn’t be ? Thanks in advance for any help you can offer .. Russ

Oohhhh nice Wasn't off eBay a couple weeks back was it? Where about are you located? Plenty of info on here, But how old, what water, Jake

Hi Russ, welcome to the forum. Is the machine in working order? As Jake has already asked, what type of water are you using as descaling the V might be tricky? It is a great machine that gives their owner the opportunity to experiment in a broad range of parameters, e.g. pressure, temperature, time, etc. to achieve some memorable results. @"DavecUK"#1 has developed, together with Paolo, the V and you could not find a better place to learn more about this machine. Parts are usually purchased directly from ACS, unless it is something very standard, e.g. E61 replacing kit. Enjoy!

@"WorldsPantry"#p37040 Welcome to the forum.

@"Cuprajake"#p37048 @ "Cuprajake"#p37048 hi Jake .. thanks for the speedy reply .. really appreciated ..no not off eBay a guy I know lives near me .. I’m in Chelmsford I think it’s a 2019 not the v10 I’m using filtered water from Brita p1000 tap..

ah, was wondering if it was a friends old machine thats all, easy way to tell the state of boilers is a tds pen, drain brew and steam boiler water in to two cups, allow to cool and see what it reads, if its really high then you may need a descale, if not great stuff

@"John_Yossarian"#p37077 @ "John_Yossarian"#p37077 hi john thanks for taking the time to answer me … it’s a great machine seems to work perfectly .. pulled some great shots already .. had and still got a rancillio silvia for the past 10 years… would like to just get to know it inside out ..

in terms of spares the group is an e61 so the service items will be normalized across the board, if you need odd stuff acs repond quick to emails : sales@mevsrl.net i would recommend a new group gasket, cafelat do the red or blue silicone seals for around £8

@"Cuprajake"#p37097 ohhh know … here we go … 😂😂 could you imagine I’m 10 years old in any further reply’s … what’s the pen … ?

@"Cuprajake"#p37099 ahhh brilliant that’s what I’m after .. help like that 😂 obvisly never seen one working so I’ve no comparisons it’s different from the diesel van that’s the rancillio

@"DavecUK"#p37083 thanks dave .. word on the street is your the go to guy for help on this machine 😂

Acs Vesuvius

WorldsPantry

JahLaza to be honest that’s exactly the sort of help or guidance I need .. I’d really appreciate any further tips .. I’m assuming you have the same machine … ?

JahLaza

WorldsPantry there are a couple of good threads on here worth checking specific to the Vesuvius

https://coffeetime.freeflarum.com/d/1462-acs-vesuvius?page=2

https://coffeetime.freeflarum.com/d/596-vesuvius-pressure-profiling-machine-general-discussion/161

DavecUK

WorldsPantry It’s fun to experiment learn and the beauty of it is, you can learn at whatever pace you want. Then save the profiles you like best.

WorldsPantry

DavecUK it’s exciting .. takes you down the rabbit hole … just a quick question Dave I’m trying to plumb this in to the mains and it didn’t come with the hose as it’s obviously secondhand. Can’t find anything in the manual either and searched extensively online . Have I assumed correctly I will need to install one of these into the bottom of the machine. 6mmx ⅜ BSPT 90° male stud elbow, push-in fitting nylon pipe/tube connector… then I can connect a piece of 6mm pipe into a T in-line with the output of my Britta water filter tap.. ??

JahLaza

WorldsPantry here is a picture of the hose that comes with it for plumbing in. Each end has a Flange with outer diameter of 13mm and it’s nut is 23mm outer diameter

DavecUK

WorldsPantry Be careful it’s a small elbow and easily damaged. They are a standard hose and should be purchasable from any espresso parts store. Just make sure it has an elbow 1 one for under the machine and the washers haven’t fallen out (I think there should be washers…). I will have to look at some of mine, as I don’t like to plumb machines in.

WorldsPantry

JahLaza ummm this is interesting as the fitting on the bottom of the machine needs a male fitting ?? This is a picture of the inlet .. with the ⅜ plug still in

Cuprajake

You need one of these

Cuprajake

And it’s ½″ bsp to smaller need to check

Cuprajake

This is the valve

Cuprajake

I think it’s ⅛″ not sure

Cuprajake

https://www.bestfittings.co.uk/shop/fill-lines-fittings/fittings/male-male-adaptors/

https://www.bes.co.uk/braided-stainless-steel-flexible-hose-1-2-x-1500mm-8106/

Plus washers noted in second link

Then all you need is ½″ bsp to what ever size John guest push fit your using

WorldsPantry

Cuprajake brilliant thankyou 👍🏼👍🏼👍🏼

DavecUK

I checked some of my plumb in fill hoses for various machines, some have washers, some have a ball compression fitting and others a different style? Seems to be a mix out there…..?

« Previous Page