Both single dose, both flat burrs, both 83mm. What are the differences?

@"Cuprajake"#p33947 Hehe yes, another similarity. So what separates them?

Pricez dunno never used either Ceado has more pedigree. Can only speak of my mazzer, think @"Systemic"#8 has experience with the e37

I'm just wondering why you would go for the Ceado if they are both nearly identical in the cup?

@"DrForinor"#p33950 not unique or specific to the Caedo necessarily but aesthetics can be a factor and so too workflow. Also dimensions including footprint. Durability, ease of cleaning, brand reputation, support, parts, warranty. As mentioned, I'm not saying these necessarily apply to the Caedo but the are factors that can make some choose a more expensive grinder when the in-cup experience may be similar to a less expensive option.

The E37SD is not a 'real' single dose grinder. It's basically an E37S without the hopper and a puffer on top*. I have not seen a DF83 'in the flesh', but looking at a couple of reviews where they dismantle it at least as far as the grinding chamber, it's not built as well as the E37S and it uses a spring-attached burr carrier. In practice, the only differences you are likely to find is that the E37SD keeps its grinding setting (burr distance) even if you take it apart for cleaning and it's easier to adjust because of the worm gear (and it's _probably_ quieter). It's also possible that the Ceado setting is more 'repeatable' because of the absence of springs in the setting mechanism. Retention on my E37S can be brought down to 0.1 - 0.3 grams by puffing the grounds out - whether they end up in the portafilter is a different matter. Polishing the exit hole from the grinding chamber has made a large difference to the amount of retained grounds without puffing (and it takes 10 minutes to do). Durability/reliability on the Ceado are tested; on the DF83 far less so. Whether both produce equally good grounds, I have no idea. The E37SD It's also more than twice the price of the DF83. ------- \* Plus a few other changes - different burrs, quick-release on the worm gear, grind switch positioned on the control panel, reduced electronic functionality (no timer), lower rpm motor and a cut-off rubber gasket on the chute. Some of these can be 'reproduced' in a standard E37S by moving a couple of hot-links on the electronic board... and the burrs and quick-release can be bought for less than the difference in price between an E37SD and an E37S.

There expensive too, There's a cheap major on eBay, in fact there's a couple. Could buy one of those and your set

I've been reading and watching a lot of videos. I would much prefer just to buy the end grinder straight away rather than get an intermediate. As far as the workflow goes I understand nothing beats the Niche. Though knowing what I'm like, I think I would prefer a cup profile from a flat burr set. But I want an easy workflow, Lagom P-64? Ceado E37SD? Is the Ceado worth it? What's the Major like? It's not a single dose though?

Mine is haha Any of these big grinders are not just pour in. They use a bellows of some sort Mine I use a brush and a second perge

@"Cuprajake"#p33964 Did you modify yours? Or they are low retention, single dose straight out of the box?

Ceado E37SD vs DF83

Systemic

Cuprajake Can only speak of my mazzer, think @Systemic has experience with the e37

Yep. Replaced a Major, I’d converted to electronic with an E37. Same 83mm burrs but more compact height-wise.

DrForinor

I do like a shorter grinder.

Cuprajake

How tall is the df83

wilburpan

Cuprajake My DF83 is little less than 370 mm tall including the bellows.

The website says that if you use the hopper, it’s 17.7 inches tall.

CoyoteOldMan

wilburpan Since this started as a comparison with the Ceado:

To the top of the adjustment ring (no bellows or hopper/rubber ring): 305 mm / 12″

To the top of the small hopper: 450 mm / 17¾"

The large hopper is ridiculously large (and stowed away somewhere), and I imagine the “SD” bellows will be somewhere around 400 mm.

Cuprajake

So about the same height as the major then

DrForinor

Cuprajake But, in general footprint, doesn’t the Major take up more space?

prezes

Yea the major is around 5cm longer and wider. I owned one converted to single dosing and loved it but couldn’t keep it due to size hence the purchase of df83

tompoland

DrForinor as the workflow goes I understand nothing beats the Niche.

There is a grinder that beats the Niche for work flow. I explain why here … https://coffeetime.freeflarum.com/blog/1253-olympia-moca-sd-first-looks-review-november-2022 and it’s a flat burr; may be just the ticket.

DrForinor

tompoland That was a brilliant read, thank you for taking the time!!

I think I have my new favourite. Now need to try and source one without any faff.

tompoland

DrForinor pleased it was helpful. Have to say that the more I use the Moca SD, the more I like it. In particular the precision when changing grind size is up there with the best of the best. Tiny adjustments make a detectable difference.

DrForinor

tompoland That’s the kind of longer term summary that is reassuring.

Do you know of any place that sells it to UK customers?

tompoland

DrForinor I do not. No doubt someone here will know.

tompoland

Just realised that I’m derailing this thread. I’ve posted the question re a UK supplier on the Moca SD review thread. Please respond there if you can help.

https://coffeetime.freeflarum.com/blog/1253-olympia-moca-sd-first-looks-review-november-2022

prezes

Bella barista is advertising the non SD model although as made to order so worth dropping them a message if they’d source it for you.

It does seem like a really good grinder

DrForinor

prezes I’m going to call them on Tuesday 🙂

TomR

DrForinor

They can definitely order the SDmodel with a 4-6 week lead time. I’m putting an order in with them tomorrow as well!

“They” being Marko at Bella Barista

But make sure you are clear between SD and D models

£1300 with BB providing customer service/warranty on Olympia’s behalf, so need to return it to Switzerland

DrForinor

It actually fits in the space to the right of my machine perfectly - as if it was made for the space. Just like the Elizabeth was made for the space where it sits right now! 🤣

DrForinor

TomR Hehehe, this is a dangerous forum! I’ll call them tomorrow.

DrForinor

TomR What’s the difference between the SD and D?

TomR

Problem is now I want a Cremina to match

« Previous Page Next Page »