I can’t seem to get rid of unpleasant harshness and dryness

MediumRoastSteam · 7 Jan

MuddyOne The coffee boiler temp will heat up the longer the machine is on, so perhaps best to put the machine in eco mode when not needing it to make coffee, or when not used for longer periods.”

As predicted.

MediumRoastSteam “Oh, that’s just perfectly normal. I wouldn’t worry about that. Those machines need a cooling flush after being idle for longer than 30 minutes”. No, no, no. It’s a dual boiler. It should not behave like that.

Total nonsense. As Jake said… It’s a dual boiler. One boiler is for brew water (i.e.: Should be kept at brewing temperature at all times) - the other other boiler is for steaming. There’s no reason for the brew boiler to overheat over time - That ’s for a Heat Exchanger machine behaviour.

They are fobbing you off.

Total nonsense.

Adrianmsmith · 7 Jan

MuddyOne

Does the pid still show the set temperature or does that change as well.

Or

Is it just that actual water that is hotter then what the machine says it is

Ie is it something along the lines of faulty relay or faulty control logic

MMuddyOne · 7 Jan

Adrianmsmith well I will run more tests in following days now that I have this device but, last test it went up to 95 degrees with off set now -4 , but after 10-15 s dropped to 90 I wanted to actually ask if that how it should look like, I understand that flushing drops temp , but that also means that after few seconds we are not brewing at regular temperature.

I will run more tests tomorrow.

Adrianmsmith · 7 Jan

MuddyOne

The offset is not time dependant.

Its just a “fudge” because the temperature probe is not at the point where you want the set temp to be correct.

It should not be used to vary the temperature over time as you require

To find out what is happening we need more info.

I.e is the heater relay doing as it is told by a faulty control circuit or logic or is it closing when it should not and heating when it should not.

Need to check the pid temp, the set point as well as the actual water temp at the time periods you have issues with .

Now you have elaborated what’s happening, offset is not your issue

MMuddyOne · 7 Jan

Adrianmsmith yeah I think something is wrong with the machine and it’s not offset , look I set off set to minus 3 and turned on machine (it started heating up from 25 degrees since last time I turned it on) after 25 minutes it reached only 84 degrees, then pid showed it dropped to 79 degrees in 30 seconds.

Second video I tested after 1h of turning it on, it reached 93-94 degrees but not 95 , something is wrong with the pid here:(

MediumRoastSteam · 24 Jan

Any updates?

MMuddyOne · 24 Jan

MediumRoastSteam

Yeah, I was going to make a summary of updates once the machine gets back to me.

Seller accepted that something is wrong, got my machine posted two weeks ago, they are sending me updates, one that temperature was unstable and they narrowed down the issue to ntc probe and fitted a new one, then they wanted to keep machine for couple more days for testing. I also asked to check the pressure as something didn’t seem to be right there too.

Couple days ago I got another update saying that they are back and forth with profitec but they are slow to reply and on top of that their thermocouple has broken and they are now waiting for a replacement. That’s all for now, they did not give me the reason of communicating back and forth with profitec though.

MMuddyOne · 2 Feb

MediumRoastSteam

My machine should come next week, they just sent me an email saying that after thorough testing they are now happy with stable temperature, espresso been delicious and consistent, they’ve been replicating shots. Also the pressure is stable. My machine should arrive soon, once we both agree on date of delivery . I’ll run some tests and see how things taste, hopefully no more harshness

Adrianmsmith · 2 Feb

MuddyOne

It would be good to see a list of what they have done and replaced ……

MMuddyOne · 2 Feb

Adrianmsmith they only have told me that ntc probe was replaced and temperature been stable when left for long periods of time, also off set been set to minus 2 as the temperature been showing 4 degrees higher of what been set.

I just sent them an email to confirm if that’s all the work that has been done 👍

Aacopl · 6 Feb

Hey, I’ve experienced a similar issue as yours; I can’t seem to get a good espresso from this machine. My current setting is 90°C with an offset of -2°C.

Do you have any updates on whether the machine has been fixed?

Adrianmsmith · 6 Feb

acopl

Have you tested your actual water temperature to see if that actually is your issue.

MMuddyOne · 6 Feb

acopl the machine should be with me tomorrow, you need to test if temperature is stable. Perhaps your boiler probe is bad too

Aacopl · 10 Feb

Hey, after conducting a few tests, I found that setting the temperature offset to -1c/-2c gave me the correct brew head temperature.

However, even at 93°C, I couldn’t get a tasty espresso. I’ve since dropped it to 86°C, and it’s much better now.

How about you? What’s your brew head temperature?

MediumRoastSteam · 10 Feb

acopl - Your machine must have a problem then. It’s just not normal to have espresso extracted with the brew head temperature being at 86C.

Adrianmsmith · 10 Feb

MediumRoastSteam

is he saying that is what the temperature is set at or is that the actual water temperature.

If it is the water temperature, maybe it is the taster 🤭🤔

Aacopl · 10 Feb

Hi guys, sorry for any confusion. I’m referring to the water temperature set on the machine, which seems quite accurate in matching the brew head water temperature as well.

I’ve adjusted the setting with an offset to -1/-2.

Adrianmsmith · 10 Feb

acopl

How are you checking the actual water temperature 🌡️?

MediumRoastSteam · 10 Feb

@Adrianmsmith - Regardless… 86C on the display is not something normally seen on this sort of machine, unless you favour very under-extracted and sour espresso.

Or the machine is overheating and giving false readings… Or something else is off.

Adrianmsmith · 10 Feb

MediumRoastSteam

Exactly, but, what im asking is

Does it say 86 on the display

What is the actual water temp.

If that is 86 then the only issue is the beans!