Burr experts

dfk41

HarveyMushman I am not even sure how I would know that the burrs were not genuine anyway.

HarveyMushman

I accidentally bought some knock-off Mazzer burrs in the Super Jolly before, used them for ages and didn’t even realise until someone pointed out the missing Mazzer stamp…

Didn’t even notice!

Tal

dfk41

Tal Kind of you. It shows he has 61 sales but when you click into it he has 2 with no feedback. I suppose with the newish Ebuy protection scheme then there is not much to lose

Adrianmsmith

I can tell you first hand (not coffee related)

Ebay is absolutely shit for sellers. The worst possible experience if you get a buyer planning to rip you off.

Ebay actively help them

Buyers have many ways to rip off sellers with no way to retaliate to the 8a5tard5.

You should he good to go!!

dfk41

Adrianmsmith I bought them for £85. I guess we will see when they turn up. I do not think Mythos OEM burrs have any markings other than the word MYTHOS on the side

Platypus

Adrianmsmith Ebay is absolutely shit for sellers. The worst possible experience if you get a buyer planning to rip you off.

Ebay actively help them

Absolutely agree with this !

HarveyMushman

Do the different manufacturer variants have the same burrs? I’ve always wondered what the difference is between the three different versions of Mythos.

HarveyMushman

Yeah it’s a joke.

More than once I’ve been absolutely done.

Sold a motorbike helmet that didn’t fit me and had just sat on the shelf for a while. The thing was immaculate, buyer got it for a song and then whinged it was ‘not as described’ so got a large refund, left negative feedback and there was f/a I could do about it.

The scumbag buyers know what they’re doing too taking advantage of it.

dfk41

The second seller came back. He was selling used burrs as originals.

dfk41

So, the seller that i bought the allegedly OEM burrs from who had bought them in error from Clumsy Goat. miraculously now has another set for sale!

https://shorturl.at/dDUQn

He must never learn from his mistakes! I will let them turn up, inspect them then if needs be test ebuyer protection!

Adrianmsmith

dfk41

I can assure you, you have nothing to worry about and you are genuine….

Tal

dfk41

He did message me to say he’d had an offer on the first set (you) and that he will be relisting another set shortly after if I was interested.

So I think he had the two sets. But hopefully legit mate. As above. Probably not a popular enough grinder, in the sense that the burrs would be easy to sell, to be worth copying the burrs for.

dfk41

Adrianmsmith I am assured!

Elcarajillo

Only just read this post, If you have not tried levering off the carrier with a screwdriver DONT !!

Levering off carriers can buckle / bend them = they will run out of true after / wobble.

Running long screws through to use as ‘jacks’ scores up the under side of the housing.

A simple puller using 3 screws a metal disc and a bolt through the centre will lift the carrier off.

Jason1wood

I’m popping over to David’s tomorrow to see if we can get the bottom burr removed. Remembering it’s reverse threaded.

Not sure exactly what you mean about disc screws and a bolt @Elcarajillo

Elcarajillo

@ dfk, sorry for tardy reply, if it is similar to other grinders the carrier is a press fit onto the shaft, often with a keyway to locate.To remove the carrier requires an even straight pull upwards. (eg Mazzer’s)

If you need more info on method I will photo puller for you. OR send it to you (puller)

dfk41

Elcarajillo Could you send a photo please Frank. I have an odd job man who is quite good but has no coffee equipment experience and I will show it to him and see what he can do. Thanks in advance!

dfk41

I found this advice online

The most common reason the lower burr holder is stuck is because the previous install did not line up the flat in the rotating burr holder with the flat on the armature. Tightening up the brass nut will force the rotating burr holder on, broaching metal, which then causes the jam situation. With the brass nut removed one can use long 4mm screws to lift the rotating burr holder off the armature. Take care to tighten the screws evenly to cause the burr holder to rise evenly. Look in the rotating burr holder and see if you can remove the aluminum that is now up in the hole. If not it is time to buy another rotating burr holder.

Does that make sense?

dfk41

« Previous Page Next Page »