Does the pid still show the set temperature or does that change as well.
Or
Is it just that actual water that is hotter then what the machine says it is
Ie is it something along the lines of faulty relay or faulty control logic
Ade Smith. ACS Evo Leva v2. Kafatek Flat max 2, ssw 2024. Mazzer Philos, Craig Lyn HG-1 prime., WW key mk1.
Adrianmsmith well I will run more tests in following days now that I have this device but, last test it went up to 95 degrees with off set now -4 , but after 10-15 s dropped to 90 I wanted to actually ask if that how it should look like, I understand that flushing drops temp , but that also means that after few seconds we are not brewing at regular temperature.
I will run more tests tomorrow.
The offset is not time dependant.
Its just a “fudge” because the temperature probe is not at the point where you want the set temp to be correct.
It should not be used to vary the temperature over time as you require
To find out what is happening we need more info.
I.e is the heater relay doing as it is told by a faulty control circuit or logic or is it closing when it should not and heating when it should not.
Need to check the pid temp, the set point as well as the actual water temp at the time periods you have issues with .
Now you have elaborated what’s happening, offset is not your issue
Ade Smith. ACS Evo Leva v2. Kafatek Flat max 2, ssw 2024. Mazzer Philos, Craig Lyn HG-1 prime., WW key mk1.
Adrianmsmith yeah I think something is wrong with the machine and it’s not offset , look I set off set to minus 3 and turned on machine (it started heating up from 25 degrees since last time I turned it on) after 25 minutes it reached only 84 degrees, then pid showed it dropped to 79 degrees in 30 seconds.
Second video I tested after 1h of turning it on, it reached 93-94 degrees but not 95 , something is wrong with the pid here:(
Any updates?
Yeah, I was going to make a summary of updates once the machine gets back to me.
Seller accepted that something is wrong, got my machine posted two weeks ago, they are sending me updates, one that temperature was unstable and they narrowed down the issue to ntc probe and fitted a new one, then they wanted to keep machine for couple more days for testing. I also asked to check the pressure as something didn’t seem to be right there too.
Couple days ago I got another update saying that they are back and forth with profitec but they are slow to reply and on top of that their thermocouple has broken and they are now waiting for a replacement. That’s all for now, they did not give me the reason of communicating back and forth with profitec though.
My machine should come next week, they just sent me an email saying that after thorough testing they are now happy with stable temperature, espresso been delicious and consistent, they’ve been replicating shots. Also the pressure is stable. My machine should arrive soon, once we both agree on date of delivery . I’ll run some tests and see how things taste, hopefully no more harshness
It would be good to see a list of what they have done and replaced ……
Ade Smith. ACS Evo Leva v2. Kafatek Flat max 2, ssw 2024. Mazzer Philos, Craig Lyn HG-1 prime., WW key mk1.
Adrianmsmith they only have told me that ntc probe was replaced and temperature been stable when left for long periods of time, also off set been set to minus 2 as the temperature been showing 4 degrees higher of what been set.
I just sent them an email to confirm if that’s all the work that has been done 👍
Hey, I’ve experienced a similar issue as yours; I can’t seem to get a good espresso from this machine. My current setting is 90°C with an offset of -2°C.
Do you have any updates on whether the machine has been fixed?
Have you tested your actual water temperature to see if that actually is your issue.
Ade Smith. ACS Evo Leva v2. Kafatek Flat max 2, ssw 2024. Mazzer Philos, Craig Lyn HG-1 prime., WW key mk1.
Hey, after conducting a few tests, I found that setting the temperature offset to -1c/-2c gave me the correct brew head temperature.
However, even at 93°C, I couldn’t get a tasty espresso. I’ve since dropped it to 86°C, and it’s much better now.
How about you? What’s your brew head temperature?
acopl - Your machine must have a problem then. It’s just not normal to have espresso extracted with the brew head temperature being at 86C.
is he saying that is what the temperature is set at or is that the actual water temperature.
If it is the water temperature, maybe it is the taster 🤭🤔
Ade Smith. ACS Evo Leva v2. Kafatek Flat max 2, ssw 2024. Mazzer Philos, Craig Lyn HG-1 prime., WW key mk1.
Hi guys, sorry for any confusion. I’m referring to the water temperature set on the machine, which seems quite accurate in matching the brew head water temperature as well.
I’ve adjusted the setting with an offset to -1/-2.
How are you checking the actual water temperature 🌡️?
Ade Smith. ACS Evo Leva v2. Kafatek Flat max 2, ssw 2024. Mazzer Philos, Craig Lyn HG-1 prime., WW key mk1.
@Adrianmsmith - Regardless… 86C on the display is not something normally seen on this sort of machine, unless you favour very under-extracted and sour espresso.
Or the machine is overheating and giving false readings… Or something else is off.
Exactly, but, what im asking is
Does it say 86 on the display
What is the actual water temp.
If that is 86 then the only issue is the beans!
Ade Smith. ACS Evo Leva v2. Kafatek Flat max 2, ssw 2024. Mazzer Philos, Craig Lyn HG-1 prime., WW key mk1.
Hi, I’m using a K-type thermocouple and placing the sensor inside the portafilter basket without any coffee grounds.
For espresso, I’m using medium-dark roasted beans.
Grinder: Niche Zero, 17 to 35 grams in 30 seconds.
Flow control to 8 ml/s.
