Ok. possibly won’t do it until its been cold, so, after the last coffee turn power off, open water outlet valve and let it run to empty.
Make sure tank is full and turn power back on to fill the boiler.
Instant cold!!
Ade Smith. ACS Evo Leva v2. Kafatek Flat max 2, ssw 2024. Mazzer Philos, Craig Lyn HG-1 prime., WW key mk1.
Tal anyway, if thats the worst issue, you should be very happy ðŸ¤ðŸ¤ª
Ade Smith. ACS Evo Leva v2. Kafatek Flat max 2, ssw 2024. Mazzer Philos, Craig Lyn HG-1 prime., WW key mk1.
Yeh, the coffee so far as been incredibly impressive, and I love the usability/workflow and build quality improvement over the Fracino.
The quality of the milk is superior also, I think the fracino was just far too aggressive for me. But I’m getting really silky milk texture from this, it’s wonderful!
Removed wrong info
Ade Smith. ACS Evo Leva v2. Kafatek Flat max 2, ssw 2024. Mazzer Philos, Craig Lyn HG-1 prime., WW key mk1.
Ade Smith. ACS Evo Leva v2. Kafatek Flat max 2, ssw 2024. Mazzer Philos, Craig Lyn HG-1 prime., WW key mk1.
Adrianmsmith roger that. I’ll remove it and upload to YouTube when I do the next vid with the top panel off
Certainly looks a bit crusty. Will video shortly
Ok done a video, but nothing visibly leaking when looking at that area during heat up?
Tal there are some white residues that is a sign that something was leaking in the past. I have not witnessed the steam you have seen so back to Adrian’s advice, source a cheap antivac valve and replace it whilst you are at it or if you wish try to clean it/descale it and grease it properly. There might be still life in it.
Current setup: ACS Vesuvius, Nuova Simonelli Mythos One. Past experience, Nuova Simonelli Apia 1 gr., San Remo Capri 1 gr., Bezzera BZ 35e, Fracino Heavenly. Anfim Super Lusso.
Contact me at: john_yossarian11@yahoo.com
Youre not looking for leaking!!
You are looking at the inside of the flexible tube.
From the photo I would say that is the issue but this is a very clean machine for 5 years old. Just shows you the quality.
Blue star are a good company If that is the exact part, I’ve had a few bits from them in the past
Ade Smith. ACS Evo Leva v2. Kafatek Flat max 2, ssw 2024. Mazzer Philos, Craig Lyn HG-1 prime., WW key mk1.
With the fault you have, you are not in a desperate rush. I would email Maria and just ask what part they use and get a price. May be worth just paying them to send you one.
Obviously anything will do so long as it has the same hose connector and thread or you have the thread adaptors.
You may find it does clean and you do not need a new one, but just in case you damage it, I would get a new one first and then you have a spare 😎
The one you have fitted has a compression fitting for the plastic tube so slightly different to the one you have sourced
Ade Smith. ACS Evo Leva v2. Kafatek Flat max 2, ssw 2024. Mazzer Philos, Craig Lyn HG-1 prime., WW key mk1.
Ade Smith. ACS Evo Leva v2. Kafatek Flat max 2, ssw 2024. Mazzer Philos, Craig Lyn HG-1 prime., WW key mk1.
So I am looking for water flow in that tube?
Yeh i just grabbed a link for the first part I found. But fair yeh it doesn’t have the correct hose connection.
More like steam at that point, so condensation,
Ade Smith. ACS Evo Leva v2. Kafatek Flat max 2, ssw 2024. Mazzer Philos, Craig Lyn HG-1 prime., WW key mk1.
Ok I’ve spotted something regarding that valve. Will upload shortly
At 18s you will see the top of the valve wet out, shortly after it hits 1bar service boiler pressure and the steam in the drip tray stops
Unless @DavecUK has other advice
I would order a new one and then decide if to clean or replace it.
If you buy from ACS, Maria it will be a direct replacement and you won’t need and adaptors etc
Its not like you need to do it tomorrow…..
Include your photo from above for their info when you enquire.
Ade Smith. ACS Evo Leva v2. Kafatek Flat max 2, ssw 2024. Mazzer Philos, Craig Lyn HG-1 prime., WW key mk1.
To me it looks like it needs 1bar or so to seal. But as it gets close to sealing the flow of steam must slow and condensation runs back towards the valve. Wetting the top of it as shown. Which is probably where all of the scale has come from around it.
I will look in this thread for Maria’s email and get a part request fired off.
Thank you everyone for helping
sales ACS [sales@mevsrl.net](mailto:sales@mevsrl.net)
How to solve a problem, contact Maria. 🥰
Ade Smith. ACS Evo Leva v2. Kafatek Flat max 2, ssw 2024. Mazzer Philos, Craig Lyn HG-1 prime., WW key mk1.
