Lawn, garden and DIY cupboards projects - What are you guys doing ?

LMSC What do guys do for the extractor? They cost the same, if not more.

If cutting outside, still use decent protection - I recommend the JSP Force 8. Sheet material especially is bloody horrible - don’t want it in your lungs.

Extraction helps a lot with routing in terms of seeing what’s going on.

If you don’t need power pass-through I’d recommend CamVac.

If you want another DIY project you could mock up a master/slave using the Kemo module - decent rating - for convenience.

One more recommendation for Festool - not just the plunge saw, but the OF1400 router. I haven’t used the Bosch (which by all accounts is excellent too), but I found an open-box OF1400 on eBay at a great price, and I haven’t looked back. It’s an excellent tool, and as long as it’s connected to a shop vac (not the Festool mortgage-requiring type) there is practically no dust, even when working on MDF.

On the ¼ vs. ½″ collet, I would go diametrically (!) opposite - unless you are planning to use the router only as a trim router. You can fit a ¼″ collet on a ½″ capable router body, but you can’t do the reverse, and any shaping/moulding capability is severely restricted if you only have ¼″ bits.

LMSC Take a look at Axminster Tools to view variety of makes / models.

About 28 years ago I totally transformed our sloping back garden from this…

to this…

At the time I chose to use wood to make a decked area and a product called Woodblox for the beds due to cost. It was cheaper then than building retaining walls and backfiling and laying slabs and stone steps. Now though, I wish I had waited and saved up a bit and gone down the brick/patio slab route, as even though everything was pressure treated and looked after every year, it has rotted in places. Because it was built so long ago I can no longer get the same size decking, which means replacing the whole lot and as we all know, the price of wood now is rediculous.

So, I am now thinking brick retaining walls and slabs will at least see me out. Trouble is, I’m 30 years older and no way can I do it. Also, we have some major work being done in the house replacing all the lower ground joists and floors throughout (cowboy house builders say no more) back end of September, so it’s going to have to wait another year or two at least.

Wood decking looks good, but if I had my time again, I wouldn’t.

LMSC We have a gardena 6 zones digital timer controlled irrigation along with 6 zones distributor. At the moment, We are using only one; plan to use 3 more of these for the lawn, front and split the watering for plants. We will still have 2 spares. 😊

What is your pressure like? You might find if you want to run 2 pop ups at the same time, that you would need larger supply hose than this would take, or you would have to run 2 hoses all the way from this to each pop up, does depend a bit on size of garden and how easy it is to hide them. At the very least you will be burying pipe for the pop ups and the tree irrigation and you will need to make sure the hose you use and connectors are up to the job. I wouldn’t want to bury a normal garden hose and click connector as I know how often they leak above the ground as bits become loose. Hopefully you will be able to connect MDPE supply pipe to this controller.

If not, you will be looking at solenoid valves (all easy to do) and a 12v controller (and might be able to help you out there).

@LMSC You may have done this already, but I highly recommend a programme of removing the thatch from your lawn(s) on a regular basis, I started doing this two years ago on a very tired, run-down lawn and it makes a world of difference. Use an electric powered “scarifier” rather than a manual scarifying rake. The lawn will look pretty roughed up to begin with but will soon recover.

LMSC This is absolutely beautiful. What a grand design and development! Well done. Retaining walls and slabs will be very expensive! Let me think about it as we plan to extend the back garden enhancement this season and aim to wrap up everything next, if we can’t finish this season. It’s mostly a one-man job. It takes time, unfortunately. 😊

Thanks. Those pictures were taken when I had finished the main work. The bricks and pieces of wood on the beds were to stop the local felines doing their business and had to stay unti I managed to find a way using slightly raised chicken wire to stop them and until plants were established. As I said that was years ago and now it all needs replacing. Also, virtually every year I treated the wood too which was a major job and not cheap, which you don’t need to do with brickwork and slabs.

I’m going to price up both ways and if brickwork and slabs comes close to the cost of wood either more or less, I’m going for the brickwork… maintenance free.

Pompeyexile 30 years for an “all wood” work of that type and extent is fantastically good durability.

Perhaps a mad idea, but - depending on what is rotting, and how much - would recycling most of the current “healthy” decking and adding new (similar or deliberately dissimilar) decking “around the edges” be feasible? It may be cheaper than replacing everything…

So had a right couple days of it and im propper annoyed

The company supplying the grass and decking were ti deliver yesterday. The dacking came with a grass to follow at some point. It came at 7pm. One man on his own with 7mx5m of grass

So today i un pack and start doing the grass, theres no driver bit for the decking screws so had to order that last night off Amazon. Came today at 3, with all the excitement, i lay the grass and trum, then remembered id the sample in the car, only the wrong grass!!! Now i questioned this pre order, so today spoke to the owner, tough poo you cut it !!!

So suck it up, and lay it. Do the decking and heres the next kicker. I built my frame to spec to finish on 44 boards.

Asked the company the size of the board, 150mm. Not an odball is it, nope true 150mm

Turns out there 147mm ffs, so i have lost 130mm over the run and now have a 20mm gap. To say im annoyed is an understatement.

So heres the end of todays work

LMSC simonc I don’t remember. I remember measuring 2 or 3 bars! I was planning to bury PVC pipes. Does it work? How is it different to to MDPE

That’s the problem in the UK, our domestic pressure is so low. 3 bars will be ok, 2 might be too low but you need to check flow and importantly pressure whilst a tap is full open too.

I am just getting mine set up and cleaned and tested again and was reading up on the specs.

The karcher patio cleaner is amazing, the enclosed one