Adrianmsmith apologies for the confusion I’ve caused with that, the valve circled below was oriented the opposite way when in use and when I replaced

JahLaza The tube you circled is not where the valve seals. Clearly the vent valve is the wrong way up, but the red arrows show the valves viton seal and the seat is inside the tube, also shown with a red arrow. Check they are clean.

    DavecUK yes, it was the wrong way up in the picture I took, it was the right way up anytime it’s been in place. Thanks for informing the identity of the valves.

    my question was then on to the very bottom piece/tube/barrel, is there any internal part in that? If yes, can that be removed?

    L’autre problem - what’s your thoughts on the straight 10 bar shot? It’s discharging water to the drip tray excessively for the entire shot. Many thanks in advance

      JahLaza

      Also I believe the picture shows the other parts in the correct orientation.

      Ade Smith. ACS Evo Leva v2. Kafatek Flat max 2, ssw 2024. Mazzer Philos, Craig Lyn HG-1 prime., WW key mk1.

      About Me

        Adrianmsmith ok, cool, that’s what I was trying to figure, because I think the part you circled red is causing my issue, and I was wondering how I might remove it. According to your diagram I should be able to remove it from the top of the barrel?

        Ade Smith. ACS Evo Leva v2. Kafatek Flat max 2, ssw 2024. Mazzer Philos, Craig Lyn HG-1 prime., WW key mk1.

        About Me

          Adrianmsmith ok, tongue in cheek! Please appreciate my ignorance in the E61 arena!! I disassembled again, easily removed that piece which I see just sits there and couldn’t be contributing to my issue! I changed the spring for the spare one supplied by acs which is longer but has less tension, and that has resolved the issue although it’s a little too loose id say, so, the issue was the spring me thinks.Apologies to you and @DavecUK for all my questions on that 😌

            JahLaza The spring you used was the longer preinfusion spring that is normally not used. They leave it in the bag in case you with to enable the preinfusion chamber for some reason.

            JahLaza

            It’s not a spare. Count the turns on the ones you have against my picture and ensure the correct springs are used. The “spare” is from the un-mod’d preinfusion chamber.

            Ade Smith. ACS Evo Leva v2. Kafatek Flat max 2, ssw 2024. Mazzer Philos, Craig Lyn HG-1 prime., WW key mk1.

            About Me

            Thanks folks, I quickly realised that when I tried it out at temp/pressure. The other spring back in now. It does seem like the spring is the cause of the stiff lever action for venting though? I might look for a replacement… Any thoughts on the excessive water discharge issue?

              JahLaza

              Also!!!

              The piece you had “stuck”. Small face goes down not up. If you think of it as a top hat it goes upside down.

              Ade Smith. ACS Evo Leva v2. Kafatek Flat max 2, ssw 2024. Mazzer Philos, Craig Lyn HG-1 prime., WW key mk1.

              About Me

                JahLaza

                If you disassemble again please post a picture of all of the parts laid out as you will reassemble them in the orientation you intend to reassemble.

                Also confirm the cam is correct and you fitted the cam lever first then the top and bottom chambers.

                I’m still thinking assembly issue, sorry as it really can’t be wrong if it’s clean and moly on all springs and surfaces for assembly.

                Ade Smith. ACS Evo Leva v2. Kafatek Flat max 2, ssw 2024. Mazzer Philos, Craig Lyn HG-1 prime., WW key mk1.

                About Me

                  Adrianmsmith Hi, I disassembled again, here’s some pics, orientation as I disassembled and reassembled. molycote everywhere, all along spindle, all around cam, all around valves where they meet anything else, put back together again, cam first, top barrel, bottom barrel, lever, and it’s still stiff. The only time it hasn’t been stiff is when I changed that spring!


                    Adrianmsmith yeah that wasn’t an issue, it was sitting correctly, I was just unfamiliar with it and had ruled everything else out, apologies for going on about it - speaking about your post with the diagram, piece I thought was stuck

                    DavecUK Hi Dave, that sits in the bottom barrel, as per my previous post to @Adrianmsmith just now, I had thought that was causing an issue due to my lack of knowledge but it obviously wasn’t, so, that went back in as it had come out, sitting down snug into the bottom barrel. I had never removed that before yesterday, so it’s not causing any issue

                      JahLaza is it a viton rubber seal or a metallic spacer?

                      Below is a generic E61 group (not a Vesuvius one) disassembled and all the parts in the right place.

                        DavecUK Photo from when I had mine. The “top hat” sits upside down as it were - under the spring.

                        Ade Smith. ACS Evo Leva v2. Kafatek Flat max 2, ssw 2024. Mazzer Philos, Craig Lyn HG-1 prime., WW key mk1.

                        About Me